Arduino MKR FOX 1200 – ABX00014

En stock

34.50 HT

MKR FOX 1200 est une carte puissante qui combine les fonctionnalités de connectivité Zero et SigFox. C’est la solution idéale pour les décideurs qui souhaitent concevoir des projets IdO avec une expérience préalable minimale dans la mise en réseau avec un périphérique à faible consommation. Vous bénéficierez d’un abonnement gratuit de 2 ans au réseau Sigfox avec la carte (jusqu’à 140 messages par jour), ainsi que d’un accès gratuit au service de géolocalisation de Spot’it, qui vous permet de suivre la carte sans GPS ni matériel supplémentaire.

Qté
  • Arduino MKR FOX 1200 has been designed to offer a practical and cost effective solution for makers seeking to add SigFox connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a ATA8520 SigFox module.The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the Zero board, the usual rich set of I/O interfaces, low power SigFox communication and the ease of use of the Arduino Software (IDE) for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power (5V) to the board. The Arduino MKR FOX 1200 is able to run with or without the batteries connected and has limited power consumption.Warning: Unlike most Arduino & Genuino boards, the MKRFOX1200 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.You can find here your board warranty informations.

    Check your area coverage on the SigFox website

    Getting Started

    You can find in the Getting Started section all the information you need to configure your board, use the Arduino Software (IDE), and start tinker with coding and electronics. Full details and examples on how to use the SigFox interface are available in the SigFox Library reference page.

    Need Help?

Microcontroller

SAMD21 Cortex-M0+ 32bit Basse consommation ARM MCU

Board Power Supply (USB/VIN)

5V

Supported Battery(*)

2x AA or AAA

Circuit Operating Voltage

3.3V

Digital I/O Pins

8

PWM Pins

12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 – or 18 -, A4 -or 19)

UART

1

SPI

1

I2C

1

Analog Input Pins

7 (ADC 8/10/12 bit)

Analog Output Pins

1 (DAC 10 bit)

External Interrupts

8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 – or 17)

DC Current per I/O Pin

7 mA

Flash Memory

256 KB

SRAM

32 KB

EEPROM

no

Clock Speed

32.768 kHz (RTC), 48 MHz

LED_BUILTIN

6

Antenna power

2dB

Carrier frequency

868 MHz

Working region

EU

Length

67.64 mm

Width

25 mm

Weight

32 gr.

Avis

Il n’y pas encore d’avis.

Soyez le premier à laisser votre avis sur “Arduino MKR FOX 1200 – ABX00014”

Votre adresse de messagerie ne sera pas publiée. Les champs obligatoires sont indiqués avec *

Top